Oil Water Separators
MAK Water’s Clearmake™ oil and water separators are designed to remove free floating hydrocarbons such as diesel, hydraulic fluid and oil as well as heavier suspended solids from a wastewater stream. This form of oily water treatment is the minimum required prior to trade waste (sewer) discharge for any wash bay where hydrocarbons may be present.
Clearmake™ Separators are approved by:
Sydney Water – Ref: 2006-365
WA Water Corporation – Ref: JT1 2010 01224V01
Clearmake™ Separators test results and
Water Services Association of Australia (WSAA) independent product appraisal report
CONSTRUCTION
MAK Water Clearmake™ oil & water separators are constructed from high quality 304 stainless steel. They can however be upgraded to 316 grade stainless steel for marine or corrosive environments. Larger models have frames manufactured in hot dipped galvanised steel.
Superior Vertical Tube Coalescing (VTC) technology facilitates improved oil separation, via the unique spiral tubes, designed to assist in exercising the free floating oils to the surface. These specifically designed VTC blocks also provide optimum flow, serviceability and durability.
TREATMENT RATES
Standard treatment rates range from 800 to 56,000L/h and custom systems can be manufactured to treat flow rates in excess of 250,000L/h.
CONTROL SYSTEMS
Clearmake™ controllers are manufactured to Australian Standards and configurations are available to meet Council requirements Australia wide. All separator control systems can be designed and manufactured to meet higher IP ratings, intrinsically safe standards for hazardous areas, spill control and general or specific mine specifications. The Clearmake™ standard controller comes with IP 53 rated GPO to facilitate site installation and pump replacements. Higher IP rated enclosures are available upon request.
If you have specific requirements, contact us about our custom water clarification systems.
STANDARD SPECIFICATIONS
| Parameter |
Units |
CB1.0 |
CL1.5 |
CL3.0 |
CL5.0 |
CL10 |
CL15 |
CL20 |
CL30 |
| Treatment Rate |
L/hr |
800 |
1,000 |
1,500 |
4,200 |
7,200 |
11,000 |
15,000 |
25,000 |
| Inlet TPH |
ppm |
<5,000 (Typical) |
| Temperature |
oC |
25 |
| Density of Oil |
kg/m3 |
893 |
| Density of Water |
kg/m3 |
997 |
| Viscosity |
Poise |
0.00888 |
| TPH Discharge Level |
ppm |
<10 without bag filter (<5 with bag filter*) |
| Efficiency Removal of oil droplet size |
- |
> 10µm 95% > 20µm 98% > 25µm 100% |
| Dimensions (not including WOR) |
mm |
L |
1,280
360
780 |
1,231
445
1,256 |
1,841
445
1,256 |
2,174
698
1,491 |
2,585
1,366
1,413 |
3,201
1,366
1,588 |
3,201
1,765
1,588 |
3,734
1,765
1,788 |
| W |
| H |
| Power Consumption (estimate) |
kw |
0.4 |
0.5 |
1.1 |
1.5 |
3 |
| Power Supply |
V |
AC 240 or AC 415 |
AC 415 |
| Waste Oil Reservoir |
L |
20 |
N/A |
| IP Rating |
- |
IP 53 (GPO)
(IP 54 controller optional)
|
IP54
(IP 65 optional)
|
* Bag filter only available for CL1.5 and CL3.0
The MAK Water Clearmake™ Vertical Tube Coalescing (VTC) technology is effective in removing small oil droplets, with a 95% removal rate of droplets as small as 10 micron and a 100% removal rate of droplets as small as 25 micron. Where oil droplet size is considered to be predominantly smaller than 10 micron i.e. emulsified, physical oil & water separation technology becomes less effective and Dissolved Air Flotation (DAF) should be considered.
Refer to these test results that were undertaken to demonstrate the effectiveness of the Oil & Water Separator in removing free floating hydrocarbons form a wastewater stream and the additional reduction that is possible when filter bags are used. The following independent product appraisal report undertaken by the Water Services Association of Australia (WSAA), validates the Clearmake™ design as fit for purpose to treat oily water prior to entering a sewer network.
STANDARD INCLUSIONS
✓= Standard Supply o = Optional Supply - = Not Applicable
| Equipment |
CB1.0 |
CL1.5 |
CL3.0 |
CL5.0 |
CL10 |
CL15 |
CL20 |
CL30 |
| 304 Stainless Steel Separator |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
| 304 Stainless Steel Frame |
✓ |
✓ |
✓ |
✓ |
- |
|
- |
- |
| Galvanised Frame |
- |
- |
- |
- |
✓ |
✓ |
✓ |
✓ |
| Feed Pump Diaphram |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
- |
- |
| Feed Pump Helical Rotor |
o |
o |
o |
o |
o |
o |
✓ |
✓ |
| VTC Coalescing Blocks |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
| Pump Controller |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
✓ |
| Waste Oil Reservoir |
✓ |
✓ |
✓ |
o |
o |
o |
o |
o |
| Final Bag Filter |
- |
✓ |
✓ |
- |
- |
- |
- |
- |
Disclaimer: MAK Water is continuously updating and improving its products and services, so please contact us for more detailed information or to confirm specifications. MAK Water takes no responsibility for any errors resulting from the use of information contained within this document.
